Cooper Security 9751 Manual de instalación descargar pdf (Pagina 58)

4. Programming

Page 50 496964

Command Key in:

42 Bell Duration (page 76)

42YnY

n = 1 1.5 minutes

2 3 minutes

3 5 minutes

4 10 minutes

5 15 minutes

6 20 minutes

Y

43 This command has been replaced by

Command 201.

44 Level/Partition A Exit Time (page 77)

44YnY

n = 1 10 seconds

2 20 seconds

Y

3 30 seconds

4 45 seconds

5 60 seconds

6 120 seconds

45 Entry/Exit Tone Volume (page 77)

(In a partitioned system, this Command

is available only for Partition A)

45YnY

n = 0 No Entry/Exit tone from sounder

n EE tone volume (1=low, 9=max) 5

46 Tamper Alarm Response – single

system only (page 77)

46YnY

n = 0 Internal sounders only

1 Keypad sounders only

2 Internal and keypad sounders

Y

47 Partition A Alarm Response –

partitioned system only (page 77)

47YnY

n = 0 Keypad sounders only

1 Local (all sounders, no comms)

2 Full (all sounders and comms)

Y

48 Lockout Keypads During Entry (page

78)

48YnY

n = 0 No

1 Yes

49 This command is not used.

50 CSID Code (page 78)

50YnnnnY

nnnn = Central Station ID for remote reset none

51 Set Time and Date (page 79)

51YddY

mmYyyY

hhYmmY

dd Day of the month (01–31)

mm Month of the year (01–12)

yy Year (00–99)

hh Hour of the day (01–23)

mm Minute of the hour (01–59)

52 Omit Alarm (page 79)

52YnY

n = 0 Alarm contacts only

Y

1 Alarm and tamper contacts

53 Abort Reset (page 79)

53YnY

n = 0 Use option selected in Command

33

Y

1 User reset after an aborted alarm

54 BVVO Supervision – not 9751 (page

80)

54YnY

n = 0 Disabled

Y

1 Enabled

55 This command is not used.

Command Key in:

56 4/6 Digit Access Codes – not 9751

(page 80)

56YnY

n = 0 Four-digit codes

Y

1 Six-digit codes

57 Battery Load Test – not 9751 (page

80)

57YnY

n = 0 Disabled

Y

1 Enabled

58 BVVO Tamper Indication – not 9751

(page 80)

58YnY

n = 0 User Reset

Y

1 Installer Reset

59 External Sounder Tamper (page 81)

59YnY

n = 0 Negative voltage tamper return

Y

1 End of line 2k2 resistor

60 Level/Partition B Final Exit Operation

– single system only (page 81)

60YnY

n = 0 B=FE = FE (Final Exit)

Y

1 B=FE = NA (Normal Alarm)

61 Level/Partition B Entry Route

Operation – single system only (page

81)

61YnY

n = 0 B=ER = ER (Entry Route)

Y

1 B=ER = FE (Start entry timer)

62 Level/Partition B Exit Mode (page 81)

62YnY

n = In a single system:

0 Timed low tone on setting

Y

1 Instant (no exit tone)

2 Silent (double "beep" after exit time)

3 Sets exit mode the same as Level A

In a partitioned system:

0 Timed full tone on setting

Y

1 Terminated (terminated by button)

2 Final Door (last door has a detector)

3 Instant (no exit tone)

4 Silent (double "beep" after exit time)

5 Lock Set (terminated by lock switch)

63 Level/Partition B Alarm Response

(page 82)

63YnY

n = In a single system:

0 Keypad sounders only

1 Internal and keypad sounders

Y

2 Local (all sounders, no comms)

3 Full (all sounders and comms)

In a partitioned system:

0 Keypad sounders only

1 Local (all sounders, no comms)

2 Full (all sounders and comms)

Y

64 This command has been replaced by

Command 202.

65 Level/Partition B Exit Time (page 83)

65YnY

n = 1 10 seconds

2 20 seconds

Y

3 30 seconds

4 45 seconds

5 60 seconds

6 120 seconds

1 2 ... 53 54 55 56 57 58 59 60 61 62 63 ... 147 148

Comentarios a estos manuales

Sin comentarios