Cooper Security i-on 16 Guía de usuario

Security System User Guide

Everyday Operation Page 8 Quick Set Quick Setting does not require the use of an access code or tag. (The Installer must enable this facility for you

Everyday Operation Page 9 If the System Will Not Set Normally, the system will set only when all the detectors are “quiet”, that is: not reporting

Everyday Operation Page 10 Setting With a Remote control Note: You must program the control unit to recognise ("learn") a remote control, se

Everyday Operation Page 11 Unsetting When unsetting the system do not stray from the entry route designated by the installer. If you do then you w

Page 12 3. Alarms Types of Alarm The i-on16 normally starts an alarm when it receives an alarm signal from one of its detectors. In addition, you can

Alarms Page 13 Silencing an Alarm In an alarm the i-on16 operates the siren. The siren runs for a limited time set by the installer (a maximum 15

Page 14 4. Alerts (or Why is it Beeping?) From time to time the control unit may detect that there is a problem with the system. It will try to infor

Page 15 5. Administration To make changes to the way your system works you must enter the Menu. Your degree of access to the Menu depends on what t

Administration Page 16 Omit Zones You may wish to prevent a zone causing an alarm. For example, if your garage door is protected by a detector, but yo

Administration Page 17 2. Press u or n to display the user you wish to edit, and then press >. The bottom line shows one of a list of the optio

Page ii Contents 1. Introduction... 1 Controls and Displays...

Administration Page 18 14 ghi7 pqrs* 0 #2 abc5 jkl3 def6 mno8 tuv 9 wxyzABCÆÅÄ DEFGHIJKL MNOØÖPQRS TUV WXYZSpace 0 Figure 3. Letters Assigned to Keys

Administration Page 19 Proximity Tags A proximity tag is a small plastic token with a low powered radio transmitter inside. Each tag contains a un

Administration Page 20 Remote controls A remote control is a transmitter that you can attach to a keyring. The remote control has four buttons and a s

Administration Page 21 If you do not wish to register a remote control press X. If the control unit has already learned that remote control then

Administration Page 22 unauthorised person can use it. Also, if you wish to reassign a device to another user, you must first delete it from the syste

Administration Page 23 The display asks you to assign a new user code. 4. Key in the user code you want the new user to employ. Key it in a secon

Administration Page 24 Once you delete a user, the system does not respond to their access code or to their proximity tag. In addition, the control un

Administration Page 25 Siren Press > to turn the siren on and off again. The word "On" or "Off" on the display shows whethe

Administration Page 26 The bottom line of the display shows the first item of the System Configuration menu. 2. Press u or n to scroll through the opt

Administration Page 27 Note: The internal clock does not adjust itself for daylight saving. Loudspeaker Volume You can make the tones from the int

Page 1 1. Introduction The i-on16 is a wireless intruder alarm system intended mainly for use in domestic and small commercial properties. The heart

Administration Page 28 3. Key in the new telephone number from the keypad. If necessary, press u to move the cursor left, or n to move the cursor to

Page 29 List of Menu Options Item Page Omit Zones 16 (Zone 01, 02, …) Users 18 Edit User 16 (for each user:) Name 17 Type (not U01) 18 Code 16 P

Page 30 © Cooper Security Ltd. 2008 Every effort has been made to ensure that the contents of this book are correct. However, neither the authors nor

Introduction Page 2 1. Two button panic alarm. 2. Two button panic alarm with tilt switch. 3. Two button panic alarm 4. Four button remote control. 5.

Introduction Page 3 This rest of this guide shows the simple procedures required to operate and administer the system. For information on installi

Introduction Page 4 To draw your attention to special events the rim of the navigation key glows red. The four LEDs on the right of the programming ke

Page 5 2. Everyday Operation Everyday operation involves setting and unsetting the alarm system and occasionally dealing with alarms. If you need t

Everyday Operation Page 6 Setting Note: Whenever you set the system you should first make sure that all doors and windows are secure. Full Set When th

Everyday Operation Page 7 At the end of the exit time the exit warning tone stops and you should hear a double “beep” confirmation tone to let y