Cooper Security 9751 Guía de usuario Pagina 43
- Pagina / 96
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
2. Programming Commands
497096, issue 3 Page 37
05 Walk Test: active during both engineer and user Walk Tests and
during the time between silencing and resetting the system. It is used
on movement detectors that are able to switch off the Walk Test lamp
in any state other than a Walk Test.
06 Ready Lamp: active when the system is unset and if there are no
faults. It is inactive when the system is full or part set, during any
alarm or if a circuit fault prevents setting. It is also active when the
control unit is in installer mode.
07 24-hour Alarm: activated when a zone designated as 24-hour is
violated and deactivated when the system is disarmed.
08 Strobe: activated during an alarm and deactivated when the system is
disarmed.
09 Smoke Reset: designed to be connected to low-voltage smoke
detector reset terminals. It is active for 3 seconds when the system is
reset after an alarm.
10 Siren Test: activated when the user performs a sounder test.
11 Strobe Set A: active for 10 seconds after the system (or any partition)
is set. It can be used to operate the Strobe output to give a visual
indication that the system has completed setting.
12 Pulse Set 1: active for the time set by Command 170 when someone
sets the system (same as type 26).
13 Pulse Unset 1: active for the time set by Command 172 when
someone unsets the system and during a Fire alarm or PA (same as
type 30).
14 Alarm Confirm: active during a confirmed alarm.
15 Set Complete: active for 10 seconds after someone sets the system.
16 Unset Complete: active for 10 seconds after someone unsets the
system or disarms it after an alarm.
17 System Alarm: activated when the control unit raises a System Alarm.
In a partitioned system, the following options (18-25) are also available:
18 Bell Partition A: active when an alarm occurs in Partition A.
19 Bell Partition B: active when an alarm occurs in Partition B.
20 Bell Partition C: active when an alarm occurs in Partition C.
21 Bell Partition D: active when an alarm occurs in Partition D.
22 Strobe Set A: active for 10 seconds after Partition A is set.
23 Strobe Set B: active for 10 seconds after Partition B is set.
24 Strobe Set C: active for 10 seconds after Partition C is set.
25 Strobe Set D: active for 10 seconds after Partition D is set.
- Contents 3
- List of Figures 6
- 1. INTRODUCTION 7
- Operating Modes 8
- Entering Installer Mode 8
- Leaving Installer Mode 9
- Performing an Engineer Reset 10
- Adding and Deleting Tags 11
- To Add a Tag 12
- To Delete a Tag 12
- 2. PROGRAMMING COMMANDS 13
- Zone Attributes 17
- 20: Change Engineer Code 19
- 21: Zone Configuration 20
- 22: Loudspeaker Chime 20
- 23: Remote Reset Enable 21
- 28: Status Display 22
- 29: Entry Alarm Delay Time 23
- 30: PA Response 23
- 32: Keypads and Partitions 23
- 34: PA User/Engineer Reset 24
- 35: First Circuit Lockout 24
- 36: Alarm Abort 24
- 2. Programming Commands 26
- Page 20 497096, issue 3 26
- 40: System Auto Rearm 27
- 41: Bell Delay 28
- 42: Bell Duration 28
- 43: Not used 28
- 45: Entry/Exit Tone Volume 29
- 46: Tamper Alarm Response 29
- 49: Duress Code 30
- 50: CSID Code 31
- 51: Set Time and Date 31
- 52: Omit Alarm 31
- 54: Supervision Time 32
- 55: Supervision Response 33
- 59: External Sounder Tamper 34
- 2. Programming Commands 35
- 497096, issue 3 Page 29 35
- 64: Not used 36
- 67: Forbikobler Approved 37
- 68: Forbikobler Door Timer 37
- 69: Forbikobler Door Locking 38
- 74: Not used 39
- Page 34 497096, issue 3 40
- 78: Not used 41
- 80: Forbikobler Chime 41
- 81 to 84: Output n Type 42
- 497096, issue 3 Page 37 43
- 86: Not used 44
- 87: Keypad Dual Key Alarms 45
- 89: Alarm Confirmation 46
- 90: Event Log 46
- 91 to 96: Testing Outputs 46
- 97: Engineer Walk Test 46
- 98: Load Full Defaults 46
- 99: Leave Installer Mode 47
- 100: Not used 47
- 101: Call Mode 47
- 103: Reporting Type 48
- 104: Not used 48
- 105: Static Test Call 49
- 106: Line Fault Response 50
- 107: Not used 50
- 108: Dynamic Test Call 50
- 110: Download Mode 51
- 111: Modem Speed (9853 only) 51
- 112: Rings to Answer 52
- 113: Answer on One Ring 52
- 114: Access Mode 53
- 117: Account Number 54
- 121: Not used 54
- 123: Report Restores 55
- 124: Reverse Open/Closed 55
- 126: Select Language 56
- 127: Not used 56
- 128: Not used 56
- 130: Not used 56
- 131: SIA Report Mode 57
- 137: AC Fail Override 61
- 138: Line Fault Override 61
- 140: Fault Override 62
- 141 to 142: Not used 62
- 144 to 150: Not used 63
- 159: Invert Plug-by Outputs 65
- 160: Confirmed Alarm Timer 65
- 165 to 169: Not used 67
- 176 to 179: Not used 68
- 180: Print Log (9853 only) 69
- 181: Enable Guard Code 69
- 183: Set Display Line 2 69
- 185: Keyswitch Auto Reset 70
- 187 to 190: Not used 70
- 200: Forbikobler Entry Timer 72
- 497096, issue 3 Page 67 73
- 215 to 218: Output n Type 74
- 3. TESTING COMMANDS 75
- Event Log Messages 76
- 4. SYSTEM CONFIGURATIONS 81
- Programming Partitions 82
- Common Areas 84
- 4. System Configurations 85
- 497096, issue 3 Page 79 85
- 4. System Configurations 86
- Page 80 497096, issue 3 86
- 497096, issue 3 Page 81 87
- DD243: 2004 Compliance 89
- Alarm Filtering 90
- Programming for Compliance 92
- 497096, issue 3 Page 87 93
- Page 88 497096, issue 3 94
- Index 95
- 497096, issue 3 Page 89 95
- Page 90 497096, issue 3 96
Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad Cooper Security 9751
Los Sistemas De Control De Acceso De Seguridad Cooper Security i-on 16 Manual de instalación
(16 paginas)
(16 paginas)
Los Sistemas De Control De Acceso De Seguridad Cooper Security M-Series Guía de usuario
(68 paginas)
(68 paginas)
Los Sistemas De Control De Acceso De Seguridad Cooper Security i-on160EX Guía de instalación
(180 paginas)
(180 paginas)
Los Sistemas De Control De Acceso De Seguridad Cooper Security i-on160EX Manual de usuario
(122 paginas)
(122 paginas)
Los Sistemas De Control De Acceso De Seguridad Cooper Security Homelink 75 Manual de usuario
(25 paginas)
Los Sistemas De Control De Acceso De Seguridad Cooper Security 9751 Guía de instalación
(96 paginas)
(96 paginas)
Los Sistemas De Control De Acceso De Seguridad Cooper Security i-onEX Manual de usuario
(16 paginas)
(16 paginas)
Los Sistemas De Control De Acceso De Seguridad Cooper Security M-Series Manual de instrucciones
(71 paginas)
(71 paginas)
Los Sistemas De Control De Acceso De Seguridad Cooper Security i-on16 Guía de instalación
(90 paginas)
(90 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.498 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales