Cooper Security 9853 Guía de instalación Pagina 93
- Pagina / 102
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
496791 87
5. Testing
5. Testing
Reading the Log (Command 90)
The control unit keeps a log of recent events The log can contain up to 500
events. Each event is represented by a short text message, shown below
and on the next page. To review the event log, make sure the system is in
programming mode, then:
1. Key in 90 .
The display shows the most recent event in the log. For a list of the log
messages see below.
2. Key in 1 to show earlier events or 3 to see more recent events.
3. Key in 0 to print the log if there is a printer attached to the system.
4. Key in 7 to toggle a logging printer on or off. (The keypad gives a chime
tone when switching the logging printer on, and a "beep beep" confirm
tone when switching the printer off.)
5. Press to toggle between the event message and the event time.
6. Press to leave the log.
The table below and on the next page shows all the messages that can
appear in the event log. The left hand column shows the messages that
appear on a keypad display. The middle column shows the corresponding
messages that appear in a printed log. Note that each event in a printed log
is preceded by the date and time in numerical format.
Note that neither the Installer nor the user can erase the log.
In the log user codes are represented by numbers as follows:
U00 Installer U19 Idle
U01 User code 1 U20 Telecommand
... ... U21 Keyswitch
U16 User code 16 U22 Remote Reset
U17 Duress code U23 Download
U18 Control Unit U24 Virtual keypad
- INSTALLATION AND 1
- PROGRAMMING GUIDE 1
- Contents 3
- 496791 iii 5
- 1. INTRODUCTION 7
- 2 496791 8
- 496791 3 9
- System Features 10
- Detectors 10
- 9955 Radio Expander 10
- Partioned or Single System 11
- User Control 11
- Configurations 11
- 6 496791 12
- 2. Technical Description 13
- Compatible Equipment 14
- Control Unit PCB 15
- 9954 Expander 16
- 3. INSTALLATION 17
- Cabling Keypads and Expanders 18
- Fitting the System 19
- Fitting the Control unit Case 19
- Fitting a 9930 Keypad 19
- Wiring the Control Unit 20
- Cable Entries 20
- Mains Connection 20
- Remote Keypads 21
- 16 496791 22
- Detector Circuit Connections 23
- 18 496791 24
- Connecting Expanders 25
- Expander Addressing 26
- Using Programmable Outputs 26
- Wiring Keyswitches 27
- Using a Communicator 28
- Statutory Information 29
- Application 29
- Compatible PABXs 29
- Approval 29
- Safety Notice 30
- Connecting the Telephone Line 31
- 26 496791 32
- 496791 27 33
- Fitting a Battery 34
- Initial Start Up 35
- 30 496791 36
- 4. Programming 37
- 32 496791 38
- 496791 33 39
- 34 496791 40
- 496791 35 41
- 36 496791 42
- 496791 37 43
- 38 496791 44
- Communications Programming 45
- 40 496791 46
- 496791 41 47
- 42 496791 48
- Leaving Programming Mode 49
- Engineer Reset 49
- Re-entering Programming Mode 49
- Programming Reference 50
- Country Defaults (Command 0) 50
- 496791 45 51
- 46 496791 52
- 496791 47 53
- 48 496791 54
- 496791 49 55
- RedCare Reset (Command 23) 56
- Status Display (Command 28) 57
- 52 496791 58
- System Reset (Command 33) 59
- PA Reset (Command 34) 59
- Alarm Abort (Command 36) 59
- 54 496791 60
- Bell Delay (Command 41) 61
- 56 496791 62
- CSID Code (Command 50) 63
- Abort Reset (Command 53) 64
- BVVO Supervision (Command 54) 64
- Sounder Tamper (Command 59) 65
- 60 496791 66
- 496791 61 67
- 62 496791 68
- 496791 63 69
- 64 496791 70
- 496791 65 71
- 66 496791 72
- 496791 67 73
- Call Mode (Command 101) 74
- Reporting Type (Command 103) 75
- 70 496791 76
- Dynamic Test (Command 108) 77
- Rings to Answer (Command 112) 78
- Access Mode (Command 114) 78
- Account Number (Command 117) 79
- 74 496791 80
- 496791 75 81
- 76 496791 82
- Report Mode (Command 131) 83
- 78 496791 84
- 496791 79 85
- 80 496791 86
- 496791 81 87
- Partition Programming 88
- Introduction 88
- Command Changes 89
- 84 496791 90
- ACPO DD243: 2002 Compliance 91
- Alarm Filtering 92
- 5. Testing 93
- Keypad and Event Log Displays 94
- 496791 89 95
- Printing the Log 96
- 496791 91 97
- 92 496791 98
- 496791 93 99
- 94 496791 100
- 496791 95 101
- DECLARATION OF CONFORMA NCE 102
Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad Cooper Security 9853
Los Sistemas De Control De Acceso De Seguridad Cooper Security 9752 Guía de instalación
(44 paginas)
(44 paginas)
Los Sistemas De Control De Acceso De Seguridad Cooper Security Homelink 75 Manual de usuario
(32 paginas)
(32 paginas)
Los Sistemas De Control De Acceso De Seguridad Cooper Security i-on40 Manual de usuario
(36 paginas)
(36 paginas)
Los Sistemas De Control De Acceso De Seguridad Cooper Security Homelink 75 Guía de instalación
(32 paginas)
(32 paginas)
Los Sistemas De Control De Acceso De Seguridad Cooper Security 9751 Manual de instalación
(148 paginas)
(148 paginas)
Los Sistemas De Control De Acceso De Seguridad Cooper Security 9651 Manual de instalación
(88 paginas)
(88 paginas)
Los Sistemas De Control De Acceso De Seguridad Cooper Security i-on40 Guía de instalación
(116 paginas)
(116 paginas)
Los Sistemas De Control De Acceso De Seguridad Cooper Security i-on 16 Guía de instalación
(28 paginas)
(28 paginas)
Los Sistemas De Control De Acceso De Seguridad Cooper Security i-on 16 Manual de instalación
(16 paginas)
(16 paginas)
Los Sistemas De Control De Acceso De Seguridad Cooper Security M-Series Guía de usuario
(68 paginas)
(68 paginas)
Los Sistemas De Control De Acceso De Seguridad Cooper Security i-on160EX Guía de instalación
(180 paginas)
(180 paginas)
Produits connexes et manuels pour Câbles coaxiaux Philips SWV2152W/10
© 2020, manymanuals.es. Todos los derechos reservados | 0.019 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales