Cooper Security M2000 Guía de usuario descargar pdf (Pagina 169)

161

Engineer Quick Reference

Engineer Menu 1

1-1 Program Zones

Zone type:

0= Not Used Shunt Key

1= Normal Alm Tamper

2= 24 Hour Perimeter

3= PA Silent Lock Set

4= PA Audible PSU Battery

5= Fire PSU Fuse

6= Technical PSU Power

7= Final Exit Masking

8= Exit Term Occupancy

9= Entry Security

Keyswitch Shock Entry

Attributes (toggle to change to YES/NO):

1= Access Chime Tone 3

2= Double Knock Inverted

3= Soak Test Shuntable

4= Omittable Beam Pair

5= Reset Monitored

6= Masking Non Latching

7= Entry Supervision

8= Chime Tone 1 Activity

9= Chime Tone 2

p20

1-2 Zones Advanced

Zone resistance:

1= 4K7/2K2(CC) 3= 4K7/4K7

2= 1K0/1K0 4= 2K2/2K2

Zone Output Group

p32

1-3 Ward Options

p34

1-3-1: Equipment to Wards

p34

1-3-2: Attributes

01= Conf Reset 09= Re-arms

02= Unconf Reset 10= Secure Ward

03= Tamper Reset 11= Bell & Strobe

04= Remote Reset 12= Foyer Mode

05= Panel Tamper 13= Unset Fire

06= Panel Speaker 14= Multiply Ack

07= Aux/ Bell Tamp 15= Entry Unset

08= Payment Timer 16= Entry=F/E

p35

1-4 Outputs

Output type:

1= Panel 4= Equipment

2= Digi H/Wired 5= O/M Modules

3= Digi On Board 6= Custom Outputs

Follows:

1= System 4= User

2= Ward 5= Zone Output Group

3= Zone

If following the system:

000= Bell (SAB) 059=PSU - Power

p39

001= System Strobe 060=General Fault

002= Switch 12 Volts 061=Mask Tamper

003= Detector.Reset 062=Mask Fault

004= Walk Test 063=Mask Alarm

005= Alarm 064=Fault 4k4

006= Panic Alarm (PA) 065=Pending

007= Fire Alarm 066=Always off

008= System Set 067=Ext. Line Fault

009=System Full Set 068=ATS Test

010=System Open 069=Ready to set

011=Confirmed 070=Auxiliary Fuse

012=Courtesy Light 071=Bell Fuse

013=Engineer On Site 072=Network 1 Fuse

014=Active Omit 073=Network 2 Fuse

015=Zones Omitted 074-079=Always Off

016=24 Hour Omitted 080=Rem Batt Fault

017=24 Hour Alarm 081=Rem Mains Off

018=Zones Shunted 082=Rem Pwr Out Flt

019=Technical 083=Sys Batt Fault

020=PSTN Line Fault 084=Sys Mains Fault

021=Panel Mains Off 085-099=Always Off

022=Access Code 100=Auto-Setting

023=Soak Test Fail 101=Always Off

024=First Knock 102=Always Off

025=Digi Failed 103=Always Off

026=Digi Successful 104-108=Always Off

027=Digi Active 109=PC Output 1 On

028=2nd Entry Only 110=PC Output 2 On

029=Entry Only 111=PC Output 3 On

030=Exit Only 112=PC Output 4 On

031=Exit / Entry 113-118=Always Off

032=Exit Fault 119=Custom O/P 1 On

033=Tamper Alarm 120=Custom O/P 2 On

034=Rem Service Call 121=Custom O/P 3 On

035=Code Accepted 122=Custom O/P 4 On

036=Service Required 123=Custom O/P 5 On

037=Reset Required 124=Custom O/P 6 On

038=Strobe On Set 125=Custom O/P 7 On

039=Duress Alarm 126=Custom O/P 8 On

040=System Part Set 127-128=Always Off

041=LockSet Unlocked 129=Time Switch 1 On

042=Set Failed 130=Time Switch 2 On

043=Shunt Code 131=Time Switch 3 On

044=Random Output On 132=Time Switch 4 On

045=Modem Lockout 133=Time Switch 5 On

046=Aux/Bell Tamper 134=Time Switch 6 On

047=Panel Lid Tamper 135=Time Switch 7 On

048=Chime Mimic 136=Time Switch 8 On

049=Monitored O/P On 137=Time Switch 9 On

050=Alarm Abort 138=Time Switch 10 On

051=Rem Call Enabled 139-148=Always Off

052=Relearn Required 149= Supervision Fail

053=Always On 150= RF Jammed

054=Always Off 151= TX Low Battery

055=Battery Test On 152= Tcmd Low Batt

056=Panel Battery Fault 153= Set Pulse

057=PSU - Battery 154= Unset Pulse

058=PSU - Fuse

1 2 ... 164 165 166 167 168 169 170 171 172 173 174 ... 179 180

Comentarios a estos manuales

Sin comentarios