Cooper Security 9751 Guía de instalación Pagina 72
- Pagina / 96
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
4. Programming
66 496792
Dual (3) Reports to two different receiver numbers (see Com-
mands 115 and 116).
Operation: The communicator dials the first telephone
number and attempts to connect to the first ARC. If
received and acknowledged, the communicator dials the
second number and attempts to transmit to the second
ARC. If received and acknowledged by the second
number, the communicator will close down and the alarm
transmission will be complete. If calls to the first number
fail, then the communicator attempts to call the second
number. If the communicator fails to connect to the
second telephone number, it will close down again and re-
attempt to connect to the first telephone number. The
communicator will continue to shuttle between the two
numbers, calling each number up to 15 times, until it has
successfully called both numbers.
Note: Dual reporting does not work with SIA or CID reporting formats.
Reporting Type (Command 103)
The system offers four message formats:
Option 0 Scancom Fast
Option 1 Contact ID
Option 2 Scancom SIA Level I
Option 3 Scancom SIA Level II (does not send time and date).
Option 4 Scancom SIA Level 3
Option 5 Extended Scancom SIA Level 3
Static Test Call (Command 105)
In static testing the system makes a test call either at one particular time of
day or on one day every month.
To make calls at a set time every day press A and then key in a number
between 01 and 24 to select the time of day for the call. For example, key 18
to program the control unit to make a static test call at 6:00pm every day.
To make calls one day every month press B and then key in the day number
of of the call. The day number should be between 1 and 24. The control unit
will make a test call at 1am on the selected day.
Note that the control unit will add or subtract up to 16 minutes at random to
the time you specified. This is to make sure that the ARC is not overwhelmed
with a flood of test calls from systems that have all been given the same time.
Key in 00 to disable static test calls.
- INSTALLATION AND 1
- PROGRAMMING GUIDE 1
- Contents 3
- 1. INTRODUCTION 7
- 2 496792 8
- 496792 3 9
- System Features 10
- Detectors 10
- 9954 Hardwired Expanders 10
- 9955 Radio Expander 10
- User Control 11
- 6 496792 12
- 2. Technical Description 13
- Control Unit PCB 14
- 496792 9 15
- 9954 Expander 16
- Compatible Equipment 17
- 12 496792 18
- 3. INSTALLATION 19
- Cabling Keypads and Expanders 20
- Fitting the System 21
- Fitting the Control unit Case 21
- Fitting a 9930 LCD Keypad 21
- Wiring the Control Unit 22
- Cable Entries 22
- Mains Connection 22
- Remote Keypads 23
- 18 496792 24
- 496792 19 25
- Detector Circuit Connections 26
- Connecting Expanders 27
- Using Programmable Outputs 28
- Wiring Keyswitches 29
- Using a Communicator 29
- Internal Communicator 29
- Telephone Line 29
- Line Monitoring 30
- Statutory Information 30
- Application 30
- Compatible PABXs 30
- Approval 30
- Safety Notice 31
- Connecting the Telephone Line 32
- 496792 27 33
- 28 496792 34
- 496792 29 35
- Fitting a Battery 36
- Initial Start Up 37
- 32 496792 38
- 4. Programming 39
- 34 496792 40
- 496792 35 41
- 36 496792 42
- 496792 37 43
- 38 496792 44
- 496792 39 45
- Communications Programming 46
- 496792 41 47
- 42 496792 48
- Leaving Programming Mode 49
- Engineer Reset 49
- Re-entering Programming Mode 49
- Programming Reference 50
- Country Defaults (Command 0) 50
- 496792 45 51
- 46 496792 52
- 496792 47 53
- Analyser zone types 54
- 496792 49 55
- RedCare Reset (Command 23) 56
- Status Display (Command 28) 57
- System Reset (Command 33) 58
- PA Reset (Command 34) 59
- Alarm Abort (Command 36) 59
- 54 496792 60
- Bell Delay (Command 41) 61
- Bell Duration (Command 42) 61
- CSID Code (Command 50) 62
- Abort Reset (Command 53) 63
- Sounder Tamper (Command 59) 64
- 496792 59 65
- 60 496792 66
- 496792 61 67
- 62 496792 68
- 496792 63 69
- Guide”.) 70
- Call Mode (Command 101) 71
- Reporting Type (Command 103) 72
- Dynamic Test (Command 108) 73
- Rings to Answer (Command 112) 74
- Access Mode (Command 114) 75
- Account Number (Command 117) 76
- 496792 71 77
- 72 496792 78
- (Command 125 (9752 only)) 79
- Select Language (Command 126) 79
- Report Mode (Command 131) 80
- 496792 75 81
- 76 496792 82
- 496792 77 83
- 78 496792 84
- ACPO DD243: 2002 Compliance 85
- Alarm Filtering 86
- 5. Testing 87
- 82 496792 88
- 496792 83 89
- 84 496792 90
- 496792 85 91
- 86 496792 92
- 496792 87 93
- 88 496792 94
- DECLARATION OF CONFORMA NCE 96
Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad Cooper Security 9751
Los Sistemas De Control De Acceso De Seguridad Cooper Security i-onEX Manual de usuario
(16 paginas)
(16 paginas)
Los Sistemas De Control De Acceso De Seguridad Cooper Security M-Series Manual de instrucciones
(71 paginas)
(71 paginas)
Los Sistemas De Control De Acceso De Seguridad Cooper Security i-on16 Guía de instalación
(90 paginas)
(90 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.036 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales